P.O. Box 52, Crown Point, IN 46308
Permalyn Sealer
Prior to finishing your stock,
make sure the surface is thoroughly dry. If you stained the wood
with our Antique Wood Stain, allow a minimum of 4 hours dry time
before applying any sealer or finish. This is to insure the
solvents used in the stain do not interfere with the curing of the
finish coats.
When finishing a stock, it is important to get as much of the finish as possible, as deep as possible into the wood, to insure maximum wear resistance and protection against moisture. To this end we recommend the use of a quality wood sealer such as our Permalyn Sealer. Other commercially available wood sealers are available, but almost all of these products contain a large percentage of drying oil, such as linseed, which offers virtually no resistance to moisture damage at all. Permalyn Sealer is composed of the same base polymers used in our Permalyn Finish, except it has additional penetrating agents and a slower drying speed to insure maximum penetration.
Before starting the application of sealer or finish, be sure that the area where you will be working is thoroughly clean. Since for most of us space is at a premium, we are usually finishing in the same area where we have been shaping and sanding the stock. If this is your case, take the time to give your shop a thorough cleaning, including any overhead light fixtures which are a prime source of dust contamination.
Once your shop is clean and you have a method set up for suspending the stock you are ready to start the finishing process.
Using a soft bristled brush, apply a liberal coat of Permalyn Sealer to the entire surface of the stock. Make sure that all of wood surfaces are coated. This includes the inside of the barrel channel, under the butt and inside any mortised areas. You should apply enough sealer so that the excess is actually dripping off of the stock. Once the stock is completely coated, set it aside and allow the sealer to soak into the wood for around 10 minutes. Make sure that the stock is not resting on the floor and is well supported. After allowing the sealer to soak into the stock, carefully go over the surface and check for any areas that appear to have sealer still on the surface. Pay particular attention to the barrel channel, mortised areas and around any carving or checkering you might have. You should find that all traces have penetrated into the stock. If you do find any puddles of sealer on the stock surface, wipe it off carefully with a clean, soft cloth such as an old piece of T-shirt. If you find any excess sealer in incised carving or checkering, remove this with a soft bristled brush. We like to use an old worn out toothbrush for this. Now re-hang your stock and allow the sealer to dry. Because so much sealer has been absorbed by the stock, it is best that this first coat of sealer be allowed to dry overnight before continuing.
When the first coat of sealer is dry, apply a second coat in exactly the same manner as before. The second coat of sealer will probably not penetrate as much as the first since the first coat of sealer has sealed much of the stock. Because of this, it is very important that the visual inspection for excess surface sealer be very thorough. Allow this second coat of sealer to dry for three or four hours or until the sealer is dry to the touch. As a helpful hint, take an old piece of glass or clean piece of steel and dab on a little sealer as a cure test. Place the test sample in the same general area as your stock. When the sealer on the sample feels dry to the touch, you are ready for another application of sealer.
Continue applying sealer and allowing to dry, until you first start to notice a slight gloss build up on the stock surface. This is your indication that the sealer has done its job and you are now ready to start applying finish. The number of coats of sealer it takes to get to this point is naturally dependent on the porosity of the wood.
After the last coat of sealer has dried, you are now ready to apply the finish coats. We recommend our Permalyn Gun Stock Finish, which was designed to build more rapidly than Permalyn Sealer. It also has some unique drying properties that allow it to be applied by hand, like an oil finish.
When finishing a stock, it is important to get as much of the finish as possible, as deep as possible into the wood, to insure maximum wear resistance and protection against moisture. To this end we recommend the use of a quality wood sealer such as our Permalyn Sealer. Other commercially available wood sealers are available, but almost all of these products contain a large percentage of drying oil, such as linseed, which offers virtually no resistance to moisture damage at all. Permalyn Sealer is composed of the same base polymers used in our Permalyn Finish, except it has additional penetrating agents and a slower drying speed to insure maximum penetration.
Before starting the application of sealer or finish, be sure that the area where you will be working is thoroughly clean. Since for most of us space is at a premium, we are usually finishing in the same area where we have been shaping and sanding the stock. If this is your case, take the time to give your shop a thorough cleaning, including any overhead light fixtures which are a prime source of dust contamination.
Once your shop is clean and you have a method set up for suspending the stock you are ready to start the finishing process.
Using a soft bristled brush, apply a liberal coat of Permalyn Sealer to the entire surface of the stock. Make sure that all of wood surfaces are coated. This includes the inside of the barrel channel, under the butt and inside any mortised areas. You should apply enough sealer so that the excess is actually dripping off of the stock. Once the stock is completely coated, set it aside and allow the sealer to soak into the wood for around 10 minutes. Make sure that the stock is not resting on the floor and is well supported. After allowing the sealer to soak into the stock, carefully go over the surface and check for any areas that appear to have sealer still on the surface. Pay particular attention to the barrel channel, mortised areas and around any carving or checkering you might have. You should find that all traces have penetrated into the stock. If you do find any puddles of sealer on the stock surface, wipe it off carefully with a clean, soft cloth such as an old piece of T-shirt. If you find any excess sealer in incised carving or checkering, remove this with a soft bristled brush. We like to use an old worn out toothbrush for this. Now re-hang your stock and allow the sealer to dry. Because so much sealer has been absorbed by the stock, it is best that this first coat of sealer be allowed to dry overnight before continuing.
When the first coat of sealer is dry, apply a second coat in exactly the same manner as before. The second coat of sealer will probably not penetrate as much as the first since the first coat of sealer has sealed much of the stock. Because of this, it is very important that the visual inspection for excess surface sealer be very thorough. Allow this second coat of sealer to dry for three or four hours or until the sealer is dry to the touch. As a helpful hint, take an old piece of glass or clean piece of steel and dab on a little sealer as a cure test. Place the test sample in the same general area as your stock. When the sealer on the sample feels dry to the touch, you are ready for another application of sealer.
Continue applying sealer and allowing to dry, until you first start to notice a slight gloss build up on the stock surface. This is your indication that the sealer has done its job and you are now ready to start applying finish. The number of coats of sealer it takes to get to this point is naturally dependent on the porosity of the wood.
After the last coat of sealer has dried, you are now ready to apply the finish coats. We recommend our Permalyn Gun Stock Finish, which was designed to build more rapidly than Permalyn Sealer. It also has some unique drying properties that allow it to be applied by hand, like an oil finish.
©
2020 Laurel Mountain Forge, LLC. All rights reserved